Search results

you have to think the following way, perhaps this helps: just turning off/on effects, the button need to sent a CC command toggling the value of the respective command you want to change, e.g. turn the VHX into Mute and enable the Tuner would be CC Command #1 ---> CC 1 Toggle POWER AMP MUTE...

for me one of the most powerful controllers for that price range... unfortunately pain in the xxx to program...

Hi DRB, I might be able to guide you here a little bit, corrections welcome as I do not use the Columbus as Midi Pedal and also not the Paul. - you do not need a 7 PIN Midi cable at all, the 7 PIN is only necessary in case you want to supply Power to your midi equipment. (not sure if the PAUL...

my last contact to support has been on Saturday with 2 mins response time from Peter himself...

I think everything said, just to add, the VH4 works well at even very low Volume levels. For me it is a question regarding the settings of Channel Volume in relation to Master Volume, in general I prefer the MV not lower than 9 and Channel not lower than 11 Clock-wise, however on bedroom level...

yes please would like to have an update on that one, would simply help to organize easily when your on your own...

V30s and interesting wise Peavey Sheffield...

VH4 you can do Channel insert/serial/parallel all independently and use at same time. for my understanding only via PC so you need a patch for each sound, no independently on/off switching of loops, the overall serial is not switchable at all. The VHX can do all including Front loop also via cc..

using 2x12" RL V30, very happy on both VH4 & VHX, even at lower volume... but I do not have a direct comparison...

I was always unlucky in pitching down to get a quick Downtuning, for me this cannot really work in VHX as the Pitch is after the preamp... However, it works but I would prefer to use a second guitar for things like that. In general I rather like to set the mids at least to 6 (Clockwise), or...

Yes its possible and works, but as Sean said its a little bit tone sucker (like most pedals also from my point of view), if you only change/tune down 1-2 steps its somehow ok... but still not comparable to real tune change what went into my mind, in case you are happy with the built in effects...

I think V2 is used only CH4, so if you swapped V2/V3 I guess you swapped the faulty tube to V2, serving CH4 only...

instantly, nothing to worry about, and you have the "TAILS" option so, Reverb and Delay tails will stay when changing preset

could not agree more, master not below 9-9:30, rather lower Channel Volume in that case, afterwards it is a fine tuning between master and Channel Volume, where I personally prefer to have channel if possible between 12-1 p.m. and if your ears can still handle it starting from there to turn...

From my perspective, should not be below 9-9:30 if possible

thanks Leo, I tried 2-3 Attenuators on VH4 and VHX, and honestly said its not an improvement.... same effect with lowering master on the VH4 from my perspective, perhaps even worse...

honestly, never found that, will check, thanks a lot. @Leo Diezel any details on that? Thanks

+ mic when playing on stage (ah and do not forget the FOH Tech), however from my experience Diezel amps lead to a nice easy soundcheck, basically you are done in 2-3 sec. The Tech normally is fine with what you deliver (talking about amateur level of course) From my humble opinion, best Cabs I...

from a quick look into the manual, you would need to witch to Instant Access Mode, giving you 1-8 Footswitch for CC Commands and the lower four switches for PC Changes... The you need to assign the CC Toggle Number to the wished foot switch 1-8 MIDI Continuous Controller On/Off "By assigning...

its already there you have to send CC Messages to VHX instead of PC e.g.: CC 1 Toggle POWER AMP MUTE and enables TUNER screen. CC 2 TAP TEMPO Global CC 6 PREAMP VOLUME +3db BOOST CC 24 Toggle LOOP A CC 25 Toggle LOOP B CC 26 Toggle NOISEGATE CC 27 Toggle COMPRESSOR CC 28 Toggle PITCH CC 29...