Rig-Talk

Guitars, Gear, Tone!
It is currently Sun, Nov 18, 2018 7:56am

All times are UTC - 5 hours




Post new topic Reply to topic  [ 5 posts ] 
Author Message
PostPosted: Sat, Dec 15, 2012 3:13am 
Offline
Plank Cranker Trainee

Joined: Tue, Dec 04, 2012 12:34pm
Posts: 329
Are you human?: 951
Can I use the Roland GFC 50 Floorboard to switch between the different functions on the Diezel D-Moll?

What does the Diezel FS7HE do? How much is it and where can one buy it? I cannot find it anywhere!

_________________
Diezel VH4 KT77
Peavey 6505
Diezel Lil Fokker
Diezel 412 FL V30
Diezel 212 FL V30
ESP Horizon NT II
ESP Horizon NT II
USACG Strat Kinmans


Top
 Profile  
Reply with quote  
PostPosted: Sun, Dec 16, 2012 3:34am 
Offline
Plank Cranker Trainee

Joined: Mon, Aug 13, 2012 1:46pm
Posts: 685
Are you human?: 951
The GFC-50’s default MIDI channel is channel 1. If you wish to change the default
channel, follow this procedure:
* The MIDI channel you set will not be stored in memory. It will be necessary to set the MIDI
channel each time the unit is turned on.
1. Switch on the unit while holding the Number Shift Pedal (A/B) down.
2. Select the desired MIDI channel using the Bank Shift Buttons (UP/DOWN).
(The Bank Display shows the MIDI channel currently selected.)
fig.13
* When any of MIDI channels 10 to 16 is selected, the Dot in the upper left hand corner of the
display will light.
3. Press the Number Shift Pedal (A/B). (The MIDI channel has now been set.)

Model: GFC-50 Version: 1.00
1. TRANSMITTED DATA
●Control change
Status Second Third
BnH ccH vvH
n = MIDI channel number 0H - FH (ch.1 - ch.16)
cc = Control number 07H, 10H, 40H, 50H (7, 16, 64, 80)
vv = Control Value 00H - 7FH (Prog.1 - Prog.128)
This message can be transmitted when the external pedal is connected.
●Program change
Status Second
CnH ppH
n = MIDI channel number 0H - FH (ch.1 - ch.16)
pp = Program number 00H - 7FH (Prog.1 - Prog.128)
This message is transmitted when the patch of GFC-50 is changed.


Top
 Profile  
Reply with quote  
PostPosted: Sun, Dec 16, 2012 3:35am 
Offline
Plank Cranker Trainee

Joined: Mon, Aug 13, 2012 1:46pm
Posts: 685
Are you human?: 951
7.4.2 Single Channel Mode – Automatic Channel Recognition
Your D-Moll can automatically recognize the pedal’s send/receive channel. To get your amp
into the mood (or mode) for this, push and hold “Mute” and then activate any program
change button on your MIDI pedal. The amp will look for a program change and recognize
the channel it is being sent on. Then it will switch to this channel and stay there as soon as
you let go of “Mute”.
7.4.3 Single Channel Mode – Manual Channel Selection
If you would like to have your D-Moll on a certain MIDI channel, then we can
accommodate you here as well. Here is how this works:
Push and hold “Mute” and then turn on the preamp channels in the order that corresponds
to your midi channel preference. For example: if you want to have your D-Moll to respond
only to MIDI information that is being sent on channel 7, then you must hold the “Mute”
button down and turn the Preamp channel one selector off, channel two selector on,
channel 3 selector on. If you let go of “Mute” now, then your D-Moll is set to respond to
MIDI channel 7 only. Get it? The table below gives you the sequence for all 7 MIDI
channels.
Midi Channel Ch1 Ch2 Ch3
1 off off off
2 on off off
3 off on off
4 on on off
5 off off on
6 on off on
7 off on on
7.5 Program Information
D-Moll can remember up to 128 program changes


Top
 Profile  
Reply with quote  
PostPosted: Sun, Dec 16, 2012 3:54pm 
Offline
Plank Cranker Trainee

Joined: Tue, Dec 04, 2012 12:34pm
Posts: 329
Are you human?: 951
Thanks! That was detailed!

_________________
Diezel VH4 KT77
Peavey 6505
Diezel Lil Fokker
Diezel 412 FL V30
Diezel 212 FL V30
ESP Horizon NT II
ESP Horizon NT II
USACG Strat Kinmans


Top
 Profile  
Reply with quote  
PostPosted: Wed, Jun 20, 2018 3:27am 
Offline
Hack

Joined: Sun, Jun 10, 2018 2:05am
Posts: 3
Are you human?: 951
Is it possible to have control of the individual midi function separately? Say to turn the mid boost or fx loop on or off with out a program change?


Top
 Profile  
Reply with quote  
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 5 posts ] 

All times are UTC - 5 hours


Who is online

Users browsing this forum: No registered users and 1 guest


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
Powered by phpBB® Forum Software © phpBB Group - Terms of Use