Friedman preamp?

  • Thread starter Thread starter Aidanspaghetti
  • Start date Start date
When the amp returns, I will post pics in another thread. I don't wanna hijack this one. I recently sent the amp away to have front and back plate put on it. If you wanna see a pic without the front & back plates, please send me a PM with your email.
 
Got a few requests for pics, so I will post the ones I have. On the front left is the power switch. Next to that is full power/tweed power, complements of the Mesa power transformer (from a dual rectifier, I believe). The output tranny is a 50 watt replacement for the JCM 800 and the choke is a Marshall replacement too. I believe the OT & choke are Classictones, but I'm not 100%. The empty hole is where the negative feedback pot is being installed. Then you have resonance, presence, and gain controls on the front. The dude who built the amp did not have time to finish it, so I have recently sent it to a new builder, who is gonna replace the knobs with chickenhead knobs, install a negative feedback pot in the empty hole next to the full/tweed power switch, put on front & back plates, and install sides & a top to protect everything. On the back you see the pentode/triode switch, an input jack, 8 ohm and 4 ohm speaker outs, and bias test points with adjusters.

Yes, I like good gear. Yes, I'd love a Friedman preamp!



 
A Friedman preamp would be great.
3 full channels channels/19"/2 RU

1: Full Clean
2: BE w. C45 switch
3. HBE with JBE/Sat
switchable FX loop
remote switching: Channel 1-3, FX, I doubt we need MIDI unless Dave has this at hand

Personally I do not need a compensated out but proper interfacing to power amps, two outputs
 
Wonderful idea, would love a 3 channel Friedman preamp.

I have a BE-100 but would love a preamp to use with my Torpedo Live for home use.

Happy Holidays all!
 
Influenza":eia3h9h4 said:
A Friedman preamp would be great.
3 full channels channels/19"/2 RU

1: Full Clean
2: BE w. C45 switch
3. HBE with JBE/Sat
switchable FX loop
remote switching: Channel 1-3, FX, I doubt we need MIDI unless Dave has this at hand

Personally I do not need a compensated out but proper interfacing to power amps, two outputs
Click to expand...


Perfect !
 
i dont get the effect loop thing, preamps sounds better without it
 
As for the FX loop: It needs to sound transparent of course, but I am sure, Dave's loop does.
But having a switchable loop gives you the option to have a nice FX enabled with a certain channel. I like that idea with every amp.
 
I agree with JMP2203 that the tone is better without an effects loop. I found that out when I owned a Mesa Roadster.

That being said, I need delay; so an effects loop is necessary.
 
loops in preamps are not necesary IMO

Egnater M4, CAE 3+ and Soldanos are clear examples
 
I disagree.
The VHT GP3, Triaxis and several others are good examples.
What do you do, if you want a Delay on your clean channel but not on your lead? You will need to keep the FX in the signal chain.
You need to do additional switching, may end up having digital conversion in the signal chain and may experience latency while switching ...
I wouldn't worry about signal degradation if you can simply bypass the FX loop.

I agree to keep it simple, but I do not see why a switchable loop shouldn't be a good idea.
 
Influenza":s3309vef said:
I disagree.
The VHT GP3, Triaxis and several others are good examples.
Click to expand...

Those were designed about 22 years ago, when there was a lot
of bad gear around. without MIDI etc... so that made sense.

Loopersystems were a lot more expensive those days,
today you can buy a looper "on the cheap" (~200$)
 
Agree. You can buy a looper but this will still make the setup more complicated, more cables, MIDI etc.
I would certainly prefer a simple transparent send/return that is bypass switchable. Could be an option.
 
Badcat did one for me( its serial # 1) and hit it out of the park with what it can do.Light years of versitality beyond a typical amp head.( and I love amp heads).My 2 coins in features for a friedman pre?:3-4 space,An even more featured clean ch,(with switchable clean option/functions), and the obvious other channels would be the various SS/Cantrell/ BE100 pre's,( all with midi switchable option/ functions change in each channel), 2 outs for sure,in/out on front and back,midi & analog switching, and perhaps this would be a chance for Dave to try an even newer tone he's been chasing or looking for!..
 
Just get an Egnater M4 and have Dave make you some of these:

16046986789_b564880f68_c.jpg


Shameless plug: http://www.rig-talk.com/forum/viewtopic.php?f=6&t=164117
 
Ive got room for a CAE 3+, and a Friedman preamp in this rack.Im on board if he makes it :thumbsup:
 

Attachments

  • DSC02724.JPG
    DSC02724.JPG
    156.6 KB · Views: 7,855
Yes I still do. There might be something new on the Horizon on this front. I'm sworn to secrecy though,think you guys will love what coming.
 
RACKSYSTEMS":vfxh5fju said:
Yes I still do. There might be something new on the Horizon on this front. I'm sworn to secrecy though,think you guys will love what coming.
Click to expand...
Dont make me come back to MTS Dave.....Owned 5 of them. Lots of your mods. :rock:
Good stuff......but something new??? :D

PS..its 2 degrees in Michigan. Your not missing anything!! :lol: :LOL:
 
Really cool and new. Hang tight you will know soon.
 
You must log in or register to reply here.
Back
Top