Resuming my new project - Hilbish GT120

[MadAsAHatter]

I just received the first parts of a future project. The chassis, faceplate, and PCB come into today. I wasn't expecting it to be delivered until tomorrow so it was a nice surprise to see it a day early. This will be a Hilbish Design GT120 amp build. It's pretty much a straight clone of a 70's Matamp GT120. I intend on it being mainly a bass amp, but like that it can double for guitar if I want some stoner/doom fuzz tones.

Unlike the other amp build project I did, this one isn't a kit. I'll have to source all the parts myself and there are no full instructions. Hilbish supplied only the schematic, wiring layout, BOM, voltage chart, and a handful of build pics. I'm sure any experienced builder could make do with less. Me being pretty much a novice it feels a little intimidating without the crutch of instructions. But the layout doesn't look overly complicated where I couldn't follow it and I also feel it's another small step in my journey.

I'm not starting this right away. I'm planning on doing an Allen Chihuahua kit build first, but couldn't pass up getting the PCB & chassis for nearly half off. I saved enough that it would cover the cost of a Toneclone PT for it. While I'm working on my other projects I'll be getting the parts togther for the GT120 so I have them all in hand for when I start. I'm looking forward to the challenge of this build and having something a good bit different from my other amps.

 

[311boogieman]

*following



and good luck

 

[ClintN667]

I had the pcb from them and never bothered with it. I'm doing a pcb build now that is the same as the hillbish but the guy who did it found a couple issues with the hillbish design (I think they were missing a cap around the nfb section) and corrected it.

At any rate, if you need any help on the iron I have some info for a company that worked on the original transformers and I also have part numbers for a heybooer set that is supposed to put around 500v on the plates. I think the first company ran about 380 shipped from the UK. The heybooer was about 410 minus the choke.

 

[ClintN667]

I got a long way to go but I'm stuck until I get the transformers.

 

[MadAsAHatter]

I had the pcb from them and never bothered with it. I'm doing a pcb build now that is the same as the hillbish but the guy who did it found a couple issues with the hillbish design (I think they were missing a cap around the nfb section) and corrected it.

At any rate, if you need any help on the iron I have some info for a company that worked on the original transformers and I also have part numbers for a heybooer set that is supposed to put around 500v on the plates. I think the first company ran about 380 shipped from the UK. The heybooer was about 410 minus the choke.

I'm not overly worried about it being 100% vintage correct or not as long as there are no detrimental flaws in the Hilbish board. I'm assuming since others have built it that's not the case. My big focus is that it works and sounds decently good.

I've only done a quick search for a transformer sets and saw Mercury had some. Outside of that I haven't done much shopping around. I'll probably PM you later on about those Heyboer part numbers after I do a little more looking around.

 

[ClintN667]

I'm not overly worried about it being 100% vintage correct or not as long as there are no detrimental flaws in the Hilbish board. I'm assuming since others have built it that's not the case. My big focus is that it works and sounds decently good.

I've only done a quick search for a transformer sets and saw Mercury had some. Outside of that I haven't done much shopping around. I'll probably PM you later on about those Heyboer part numbers after I do a little more looking around.

Yeah no problem. I can send you the info for the UK made ones too.

 

[MadAsAHatter]

It took me a bit to finally get all the parts together. I'm still waiting on the transformers, but they've been ordered and I have everything else on hand.

I started doing a little bit this morning and got most of the the components on the PCB. I didn't put any of the lead wired (except one) or diodes on yet. I'll save that for later. I didn't realize how big some of those orange capacitors would be when I ordered them. I was concerned they'd be too big and get in the way of other components, but they ended up fitting just fine.

 

[MadAsAHatter]

After a couple project jumped the line and sitting on it this one for over a year, I'm finally getting back to it. I'm determined to see it through before I start any other project.

I got the transformers and some other hardware mounted and put a couple heater wires on the power tube sockets. Also, I'm in the middle of making a plexiglass faceplate that will work better with a headshell I made a while back.

 

[BeZo]

Yes!

 

[Hiwatts-n-Gibsons]

After a couple project jumped the line and sitting on it this one for over a year, I'm finally getting back to it. I'm determined to see it through before I start any other project.

I got the transformers and some other hardware mounted and put a couple heater wires on the power tube sockets. Also, I'm in the middle of making a plexiglass faceplate that will work better with a headshell I made a while back.

View attachment 416263

That looks vaguely familiar.

Hope it comes out great. It looks like a beast of an amp. I sometimes think I should have went with the EL34 loaded 120 vs the KT88 loaded 150. Don't get me wrong, it sounds amazing, but over the years between different amps I've learned I'm really an EL34 guy. Clean, dirty, or filthy it doesn't matter it's those upper mids, and the way the bass and treble compress just right when you crank them.

 

[MadAsAHatter]

I'm working on things during my breaks at work so it's been a little slow going. 20 minutes here, 30 minutes there, but I've made a little noticeable progress. I also had to order & wait on a new socket because I accidentally snapped one of the pins off. I have to double check it, but I should have the power tube sockets all wired up. The green heater wires from the PT are huge so I had to step them down to smaller wire so they fit on the pins. It could be a little neater, but everything looks solid.

Next up will probably be wiring the preamp tube sockets. I have a feeling that's going to be "fun". Looking at the diagram V1 has a lot going on with it to fit in that tight space.

 

[MadAsAHatter]

A little bit more work done. The OT, impedance selector and speaker jacks are now wired up. Of course my dumb ass went and wired everything upside down. I'm checking my work and it dawned on me. Wait a damn minute here, sumpthin' ain't right... So I had to pull it all apart and do it over again. After I got it all straightened out I figured that was a good place to stop before I fucked up something else. LOL!

 

[MadAsAHatter]

A few extra things done today. Cap cans, power, voltage selector and fuses are wired up. I have a handful of the grounding trimmed and stuck in place, but I haven't soldered any of that yet. Now that most of the transformer wires are hooked up and out the way I feel like I'm making progress.

 

[MadAsAHatter]

Small progress today. Did the star grounding and input jack. I may try to do a few other things later this afternoon, but probably won't pick back up until tomorrow.

 

[MadAsAHatter]

So V1 has all kinds of stuff going on with it in a tight ass space. All the normal leads, plus a couple resistors and caps smushed in there and connected to the drive & bass boost knob. All of that was wired as point to point. So instead of trying to cram it all in there I laid it out on a terminal strip to where it would be easier to deal with. I can't take credit for the idea though. I saw a pic of this done by someone else who was building a GT120 clone.

Probably can't see it in the pics, but its bolted to the chassis using one of the V1 screws. It fit nicely, doesn't bump on anything, and I didn't have to drill any extra holes.

PS. this made things easier, but I still hate terminal strips.