Braciola
Well-known member
Incredible sounding/ built amplifier!
Features include:
All-tube signal path. Preamp tubes are 12AX7/ECC83.
Output tubes EL34
Rectifier uses massive 3 amp 1000V ultra-fast recovery diodes (FREDs) for the utmost reliability without the RF noise “spikes” inherent in standard rectifiers.
Front panel controls/connections:
Input jack, Volume 1 (bright), Volume 2 (dark), Bass, Mid, Treble, Presence, Output Level.
Input channels are internally jumpered to allow a mix of the two volume controls to provide a wide range of tones, allowing the amplifier to work well with any guitar, either single-coil or humbucker.
Exclusive Plexi/Ali front panel switch to reconfigure the preamp section to early "plexi" style for a full rich tone (great for warm clean tones) or the later aluminum, or "ali" style preamp, which is voiced brighter and tighter in the low end (best for distortion styles). Unique frequency-compensated output level control.
Unlike most master volumes, this control doesn't get thin or buzzy as you turn the volume down.
The tonal quality rivals that of our built-in attenuators, and is infinitely variable, allowing fine control of output level.
When turned all the way up, it is effectively out of the circuit completely, so it doesn't affect the full-volume tone/signal path at all.
Effects loop:
1/4" TRS (tip/ring/sleeve) insert style jack. Nominal 0dBu level allows use of line-level effects for lowest noise levels. The TRS insert jack allows use of a single TRS cable to connect the effects, instead of the two 1/4" cables normally required for an effects loop.
Rear panel controls/connections: AC mains input, interntional voltage selector allowing operation at 100V/120V/200V/220V/230V/240V 50/60Hz, impedance selector switch for 4, 8, or 16 ohm operation, two 1/4" speaker jacks, and effects loop jack.
Also includes locking mil-style RV6L bias pot and three tip jacks for easy bias setting without having to remove the chassis from the cabinet. Solid, finger-jointed birch-ply cabinet. The head is 20" wide, 8 ¾” tall, and 9” deep. The 1x12 combo is 23" wide, 18 1/2" tall, and 10 1/4" deep.
Solid 16-gauge steel chassis, zinc-plated, yellow chromate conversion coated for durability, corrosion-resistance and appearance.
Front and rear faceplates are gold anodized aluminum for durability and a classic appearance. All hand-wired, “military style” turret-board construction, using chassis-mounted tube sockets for ease of maintenance and reliability.
Built to last. Premium, tight-tolerance parts are used for reliability, including 2W 1% carbon film and metal film resistors, 5W metal oxide power resistors, 630V axial-leaded polypropylene film/foil capacitors, and low-noise, sealed, 2W mil-style RV4 pots.
Massive, custom-wound, high-interleave transformers, rated for over twice the maximum amplifier output power, allowing the amplifier to be run full power continuously, without failures.
Output power (at onset of clipping 2-EL34 50W into 4, 8, or 16 ohms resistive load.
Price $1650 Shipped - Meticulously Packed
Will Split PayPal if that's you method of payment
Features include:
All-tube signal path. Preamp tubes are 12AX7/ECC83.
Output tubes EL34
Rectifier uses massive 3 amp 1000V ultra-fast recovery diodes (FREDs) for the utmost reliability without the RF noise “spikes” inherent in standard rectifiers.
Front panel controls/connections:
Input jack, Volume 1 (bright), Volume 2 (dark), Bass, Mid, Treble, Presence, Output Level.
Input channels are internally jumpered to allow a mix of the two volume controls to provide a wide range of tones, allowing the amplifier to work well with any guitar, either single-coil or humbucker.
Exclusive Plexi/Ali front panel switch to reconfigure the preamp section to early "plexi" style for a full rich tone (great for warm clean tones) or the later aluminum, or "ali" style preamp, which is voiced brighter and tighter in the low end (best for distortion styles). Unique frequency-compensated output level control.
Unlike most master volumes, this control doesn't get thin or buzzy as you turn the volume down.
The tonal quality rivals that of our built-in attenuators, and is infinitely variable, allowing fine control of output level.
When turned all the way up, it is effectively out of the circuit completely, so it doesn't affect the full-volume tone/signal path at all.
Effects loop:
1/4" TRS (tip/ring/sleeve) insert style jack. Nominal 0dBu level allows use of line-level effects for lowest noise levels. The TRS insert jack allows use of a single TRS cable to connect the effects, instead of the two 1/4" cables normally required for an effects loop.
Rear panel controls/connections: AC mains input, interntional voltage selector allowing operation at 100V/120V/200V/220V/230V/240V 50/60Hz, impedance selector switch for 4, 8, or 16 ohm operation, two 1/4" speaker jacks, and effects loop jack.
Also includes locking mil-style RV6L bias pot and three tip jacks for easy bias setting without having to remove the chassis from the cabinet. Solid, finger-jointed birch-ply cabinet. The head is 20" wide, 8 ¾” tall, and 9” deep. The 1x12 combo is 23" wide, 18 1/2" tall, and 10 1/4" deep.
Solid 16-gauge steel chassis, zinc-plated, yellow chromate conversion coated for durability, corrosion-resistance and appearance.
Front and rear faceplates are gold anodized aluminum for durability and a classic appearance. All hand-wired, “military style” turret-board construction, using chassis-mounted tube sockets for ease of maintenance and reliability.
Built to last. Premium, tight-tolerance parts are used for reliability, including 2W 1% carbon film and metal film resistors, 5W metal oxide power resistors, 630V axial-leaded polypropylene film/foil capacitors, and low-noise, sealed, 2W mil-style RV4 pots.
Massive, custom-wound, high-interleave transformers, rated for over twice the maximum amplifier output power, allowing the amplifier to be run full power continuously, without failures.
Output power (at onset of clipping 2-EL34 50W into 4, 8, or 16 ohms resistive load.
Price $1650 Shipped - Meticulously Packed
Will Split PayPal if that's you method of payment
Last edited:
