Funny but so true

[MadAsAHatter]

Applies to several other amps as well. LOL

 

[JackBootedThug]

Truf.

 

[RaceU4her]

i have a box full of handles and screws that i have no clue which goes with what amp

 

[Shreddy Mercury]

When I had my Budda 3/4 stack (a 412 under a 212), I had to deal with the handle on the 212 making the head ever so slightly unstable, but really no issue.

 

[Strandberg Junkie]

Reverb tank sticking out the bottom is just as bad with a Mark imo.

 

[Eazy-ESP]

I buy second hand amps and cringe every time I see amps stacked. Some of the modern tolex gets round feet marks all over it.

 

[RaceU4her]

I had to deal with the handle on the 212

my Cameron 2x12, perfect for putting an amp on top of. good job mark

 

[311boogieman]

I buy second hand amps and cringe every time I see amps stacked. Some of the modern tolex gets round feet marks all over it.

I put small pieces of black packing foam under my amp head feet to protect my cabs.

Splawn has a built in handle in their 212 cabs just like Billy Blades does.

 

[Eazy-ESP]

I put small pieces of black packing foam under my amp head feet to protect my cabs.

Splawn has a built in handle in their 212 cabs just like Billy Blades does.

I’ve really got to try a Splawn one of these days. Few and far between in Australia.

 

[Racerxrated]

I put small pieces of black packing foam under my amp head feet to protect my cabs.

Splawn has a built in handle in their 212 cabs just like Billy Blades does.

I’d skip the Blades reference.
Just sayin. ?

 

[311boogieman]

I’d skip the Blades reference.
Just sayin. ?

It was a joke. Scott has been doing that with cabs far longer than Billy did with an amp head. Good idea Billy had for doing that in a an amp head actually as long as you have room (although I don't think he was the first). Cup holder? Not so much.


Also - I just had an idea about how it would be nice if someone made slightly longer rubber amp feet. Might look a little dorky but a lot less intrusive than removing amp handles.

 

[Luca79]

The problem is the handle or too short feet?

 

[Strandberg Junkie]

Also - I just had an idea about how it would be nice if someone made slightly longer rubber amp feet. Might look a little dorky but a lot less intrusive than removing amp handles.

Have used them before. Mainly for better air flow under the head.

https://www.parts-express.com/Penn-...UCQax1jk9VeId3vCzFNFN3AW_a4OQ1yoaAmUXEALw_wcB

 

[MadAsAHatter]

Also - I just had an idea about how it would be nice if someone made slightly longer rubber amp feet. Might look a little dorky but a lot less intrusive than removing amp handles.

Have used them before. Mainly for better air flow under the head.

https://www.parts-express.com/Penn-...UCQax1jk9VeId3vCzFNFN3AW_a4OQ1yoaAmUXEALw_wcB

The standard size feet on most amps is 1/2", but those don't have quite enough clearance over the type of handle in my OP. They do have 3/4" thick ones that are tall enough to fit though.

 

[Strandberg Junkie]

those don't have quite enough clearance over the type of handle in my OP

I'm confused. The ones in the link are 1-1/2" tall and clear a Mark handle.

 

[MadAsAHatter]

I'm confused. The ones in the link are 1-1/2" tall and clear a Mark handle.

I meant the 1/2" ones aren't tall enough

 

[griff10672]

4 hockey pucks and you're all set ...