Lets see your Splawns and get some dialog started here.

gtrjunior

New member
Old pic but here’s my QR
 

Attachments

  • 89C8A066-1F38-4AFA-8586-2D13400DCC21.jpeg
    89C8A066-1F38-4AFA-8586-2D13400DCC21.jpeg
    715.9 KB · Views: 13

Briman24

Member
My fully loaded 2016 purple QR and 2015 standard QR. I sold both and miss them dearly No worries as I will be ordering a new one from Scott this summer. Gotta pick the style and colour.
 

Attachments

  • 20180315_145634.jpg
    20180315_145634.jpg
    3.6 MB · Views: 8
  • 20170523_200235.jpg
    20170523_200235.jpg
    6.8 MB · Views: 6

311splawndude

Well-known member
What do you think you will go with Briman?


And I remember your amp. You were looking for those purple chicken head knobs.
 

Briman24

Member
What do you think you will go with Briman?


And I remember your amp. You were looking for those purple chicken head knobs.
I am definitely getting QR fully loaded. The debate is between traditional black with gold piping plexi, vintage white with gold piping and pro stock in vintage white z28 stripes in black.
 

Briman24

Member
Power tube rolling would be so much easier with external bias points. That is my only complaint with the QR.
I drilled a hole in the bottom of my competition head shell 10 years ago to have a access to the bias pot. Worked great for rolling tubes.
 

kmanick

Active member
I drilled a hole in the bottom of my competition head shell 10 years ago to have a access to the bias pot. Worked great for rolling tubes.
that's great idea , I may have to do that to my super Sport, only thing is I may not have enough height inside my head shell to plug in the bias probe and then the tube into it ,so I may have to pull the chassis anyway :(
 

Briman24

Member
I used to be able to put my probes on while in the headshell. Just make sure you line up where you are going to drill the hole perfectly where the bias pot is. It was a little tricky to do.
 

Briman24

Member
I think i have pictures somewhere that i took of the hole i drilled. Will see if i can find them and post. I think it was half inch wide hole allowing a bit of room incase i wasn't 100% aligned to the bias pot.
 

311splawndude

Well-known member
I remember you doing that Briman :yes:
My weber probe is too big anyway like kmanick.
I don't mind getting in there anyway, it gives me an excuse to clean the outside of the chassis :D
Still a great idea though.
Pro Stock black with white stripes and white chicken head knobs would be sexy as hell
 

Briman24

Member
I can't seem to find the pics i took. I remember camsdad started a thread on it splawn forum. He plugged his hole with a boat plug.
 

311splawndude

Well-known member
I can't seem to find the pics i took. I remember camsdad started a thread on it splawn forum. He plugged his hole with a boat plug.

I think I found that thread but all the pic links are dead. Was it this one? Wow - 2011. Seems like yesterday but then like ages ago too :D

 

glowe

Member
Older 2004 Pre Gear - Pre Quickrod-era rarity - A Soldano SLO and Friedman BE100 retired it years ago , but it still hangs around and lives in my closet
 

Attachments

  • 111.JPG
    111.JPG
    1.8 MB · Views: 9

cvogue

Member
Where are you hearing clip of glowe? All i see is a pic of older splawn with an attenuator? No video for me?
There's a Facebook posting/link below the pic of the way old Splawn with attenuator and there are audio (Soundcloud?) clips in there.
 
Top